New Video Tutorial - Passport Card Wallet

Voyage Passport Wallet

 

Hello,

As promised in my previous post, finally the video tutorial for the small passport wallet is up on my YouTube channel now. And as I edited the original pattern to add the link, I also gave a name to the pattern. Well, I am really not good at giving names but then, as I make more patterns, I suppose it's inevitable for me to give a certain name. This time, I go with the simple name Voyage Passport Wallet. I plan to update the original pattern with better photos when I get the time, so please bear with me.

In the video, I cut the pattern pieces slightly bigger than the original one, because I want to use it for Journal Cover like in my previous post

For the zipper version, all the basics remain the same as the original pattern. If you want to make it with zipper closure, here are the additional materials to cut/change: 

✓ Cut 2 -  Medium or All-purpose interfacing for main exterior and lining

✓ Cut 1 - Fleece Batting  - the same size as the main exterior 

 ✓ #5 Zipper – 24” Long (based on the continuous zipper that is cut to size) 

✓ Bias binding (follow THIS TUTORIAL)

Without further ado, here's the video :

If you're new here and wondering about the interfacing I used in my wallets, I wrote my secret guide for interfacing in THIS POST and THIS POST. My suggestion is to keep experimenting until you find the combination that you like the most. In the hydrangea passport wallet above, I used all-purpose interfacing for the main body and using medium interfacing for the sleeves' base. The wallet turned out softer and I can even fit it with more passports - up to 4 passports and it still closed nicely. 

I made another Voyage Wallet with Snoopy Print as a custom order. Some of the crafters, DM me on Instagram asking how to do bias binding nicely. As I mentioned in my previous post, before cutting the binding (cross-cut or bias), make sure the fabric grains are straight. This small step is very important to get a good finish. And of course, practice! Practice makes improvement. Sometimes even I had to rip off the already sewn binding because I didn't straighten the grain nicely and resulted in sloppy finish. 

Zip Around Passport Wallet

Another question is, can I use cross-cut binding instead? Yes, you definitely can. I made a couple of passport wallets with zippers using cross-cut binding. It will be like the usual wallet binding, like in THIS tutorial. When you want to use cross-cut binding for a zipper wallet, do not CURVE the corners. I will make the video next time when I am working on a wallet binding. 

Here is a few Ohana Passport Wallet I did for a custom order. 

Mitered Corner binding

Cartoon Print Passport Wallet

I hope the video and a few tips above help your journey in the wallet making. Please let me know if you have any questions. 

Thank you so much for reading my blog. 

Happy Sewing,

Elvira

*****

Linking up to these wonderful BLOGS 

_______________________________

Free Pattern - DIY Dust Mask with Nose Wire

Winter in my place means dry and dusty. It's time to make a dust mask again. This time I share how to make a surgical mask type. It's super-duper easy.

All you need is :

- 2 pieces of fabrics - 7.5" W x 6" H
 (Kids Size : - 6” W x  5.5” H)
(widen and lengthen as needed)

- 2 pieces of binding strip - 1.75" w x 5" H

- 10" Long Elastic Cord

  Although cloth face mask may not be as effective as N95 mask in filtering fine dust, but it is better than nothing. I'd suggest adding a layer of folded tissue paper when you wear the mask, which I believe can screen as much as 75% of dust particles, according to THIS report. I'd suggest using tightly woven fabric for better results.

I'd also suggest to wash the cloth mask everyday after your use it. It's always better to make a few, especially if you're highly allergic to dust and pollen. I hope this little bit of information will be helpful for you. 

You can download the full PDF Version below  and start making.

Pattern Update : Added instruction for adding nose wire, as follows:

Adding Nose Wire :

I use twist and tie as nose wire, it works like a charm.  To add nose wire, BEFORE making the Pleats,  sew one line 1/4 Inch away from one of the long edges, approx 5” long and centered. 

Cut twist and tie approx 5” long (or as needed) and insert it in the tube line you just created. 

 Stitch both end of the tube to prevent the wire from sliding off. 

And now you have a surgical mask with a nose wire that can properly fit. 

I hope this helps, let me know if you have any questions. 

Buy Now

Other Mask Patterns:

Pleated Mask with Filter Pocket

Free Pleated Mask Pattern

3 D Mask with  Filter Pocket & Video Tutorial

Happy Sewing! 

- Elvira - 

Linking up to :
Sew Can Do
Handmade Monday #162

  

Video Tutorial : How to sew family passport holder

 Hello again, 

Video Part 1

Finally, I finished editing the videos for the Family Passport Wallet pattern. The supporting video tutorial comes in 2 parts. The first part is the making process of the passport slots. 

I made a few changes : 

1. The LINING for the zipper pocket, I use ONE piece of lining 5" W x 6.5" H. (in the original pattern it was 2 pieces of lining fabric). 

2. Passport Slot construction is different from what's written on the original pattern. This new way I found it better and faster to make. 

Let's jump to the video below: 

For Part 2, I am showing how to attach the zipper closure using a single tape zipper. It's the same way as the Nuno Small Wallet. For the zipper length, I use the #5 nylon zipper approximately 44-45 inches long. This is my new fave in attaching a nylon zipper. 

I hope the video will give you a clear understanding of the pattern. I will update the pattern when time permits. Do let me know what you think in the comment below.

Thank you for reading my blog.

Happy Sewing!

Elvira

Pattern Update: Adding Zipper Coin Pocket on Nuno Wallet

Nuno Wallet with Zipper Pocket 

Hello, 

A few weeks ago I had a customer asking for a zipper pocket instead of a flap pocket for the Nuno Wallet. While making the order, I decided to take photos of the process and share it with you. In this additional tutorial, I will also share how to create Faux Binding.

So without further ado, let's start.

Additional Material and Cut:

- #3 All-purpose zipper 5" long

- Cut the divider panel lining piece 4.75" wide.

Please note that this is an additional tutorial for Nuno Wallet. The original pattern may not include this tutorial.

WATCH THE VIDEO

Let's go:

1. Use #3 or an all-purpose zipper around 5" long or longer. Fold the end of the zipper tape as shown in the picture below.

2. Place the zipper right side facing down on the right side of the fabric, 1.5" away from the center crease. Baste stitch with a seam allowance of 1/8" (3 mm).

3. Now bring the left part of the pocket fabric on top of the previously sewn zipper and top stitch with a seam allowance of 1/4" (6 mm). Don't forget to backstitch at the beginning and at the end.

4. Turn the wallet right side out, poke the corner, and finger-press the seam flat. Now, top stitch with a seam allowance of 1/8" (3 mm). Trim the excess zipper tape.

5. Fold the pocket 1.5" away from the left at the point where the zipper is and top stitch with a seam allowance of 1/8" (3 mm). Backstitch at the beginning and end.

6. From this point, follow the pattern by placing the pocket panel and the card slot panel on the divider piece. Then, Place the assembled panel on the divider lining piece. Baste stitch along the sides and bottom with a seam allowance of 1/8" (3 mm).

7. Fold the extended lining piece towards the wallet's raw edge and then fold it to encase the raw edge. Make sure it covers the previous stitching line. Pin in place.

8. Carefully topstitch close to the edge.

and that's it! It's pretty simple and easy, right? Sewing a wallet or bag with a zipper is not difficult. I personally like to baste the zipper first before doing the permanent stitch. That way it will come out neater.

VIDEO TUTORIAL:

Small Bifold Wallet

Now you have an option for making The Nuno Wallet with a zipper pocket instead of a flap pocket. This Nuno small wallet is very compact and functional. With cashless payment becoming a trend everywhere now, many people carry fewer cards.

I hope you can learn a few things from the tutorial. Do let me know in the comment below if you have any questions.

Thank you for stopping by!

Happy Sewing

Elvira

Free Pattern : Pleated Face Mask with Filter Pocket

Thank you so much for your overwhelmed response to my mask tutorial/pattern. That was a pretty simple one. Many asked me to make a pleated mask with a pocket for a filter which is very necessary especially during this COVID19 Pandemic. 

In the past few days I've been making masks (with and without filter) for family, friends, and people around me. Masks are not available now and hence people resort in fabric masks. I'm very touched reading so many stories of our sewing community come together and donating masks to the hospital. I am donating a few to a nursing home near my house, they have been a great help for us for years. It's time to show our support to those who are on the front line. 

How to Wear Mask with Ties:

Here my son demonstrates how to wear a mask with ties

UPDATE

I got a few questions regarding the pocket esp from beginners, so here's the easier way to do it. I just use a screenshot here, which I hope clear enough. I already updated the file in the shops, so if you download it on 27th March at 10PM IST you should get the new one. If not, feel free to download again or simply save the photos here:

Feel free to email me if you have any doubts :)

I hope this pattern will be beneficial for you all. I will try to add video as soon as I get time to edit it. meanwhile,you can simply click the button below and download the pattern. 

Download Free Pattern

Thank you for stopping by & take care!

Elvira

Other Masks Patterns:

Breathe Easy Face Mask

KN95 Style Singer Face Mask

Dust Mask with Nose Wire

Weekends Update

I've been working on this wallet for a few days. It's super easy one but  life happens. First, my crown broke and had to spend my birthday at the dentist. Well at least I am getting something new for the birthday, right? 😄😄 

I'm super tickled when I saw the chicken print. It's too cute!! 

And my next project is all set, Insha Allah will start tomorrow. Stay tuned for new bag pattern from Bagstock!! Yes, I'm testing for Namrata's next pattern! I know you're going to love it. I am so excited to try out this vinyl after I made the origami pouch for fun! 

Sometimes, we really need to make time to learn and try new things right? And guess what? I am subscribing to SimplyPiano app on my phone and teaching my self to play piano 😄😄😄 I will update you with my progress. I am having fun practicing these few days!! 

Speaking about piano, my son's music school is closing it's door after 7 years. The above photo was yesterday, the last day we went to Ace Music! What a journey it was. Thank you everyone at Ace Music for your hard work all these years !! But the good news is he will still continue learning with Ms. Promiti Phukan in her new brand music academy, Cadenza  from April, after he finishes his board exam. Cheers to new journey! 

That's all my little update. Do not hesitate to pursue your passion. When there's a will, there's a way! 

Now, I'm going to hand sew my wallet and watching Notting Hill on Prime Video! 

If you're asking, yes..I am working on the wallet pattern.  Stay tuned!

Much love & have a nice day!

- Elvira - 

Pattern Update : Pleated Mask without Binding

Just a quick post regarding pleated mask. If you don't want to do the binding like in the original tutorial, you can do the following : 

1. Cut the fabric 9.5" Wide x 14" long. (For broader face, you can cut 10" W or as needed). The measurements in this tutorial here is based on general surgical mask.

2. Follow the tutorial for creating pocket, nose wire and pleats. 

3. Once, you're done, the mask should measure more or less as follow: (please note that you can modify the pleats, the tutorial is guidance, esp for novice sewist) 

4. Now,  fold the raw edges by 1/8" or so towards the lining side (where the pocket is) and then fold it again by 1/2" and edge stitch. (I am making mask without lining here) 

5. Insert the elastic or ties and it's ready. Super easy! Maybe a bit fiddly in the beginning but you will get the hang of it. 

Thank you for downloading the tutorial. And if you have any questions, don't hesitate to email me. 

We're all in this together and we will get through this pandemic together. Keep sewing, stay healthy and safe, everyone! 

Happy Sewing,

Elvira

Download Free Tutorial

3D Mask Pattern